Axial Fan: Common Issues and Solutions for Optimal Performance
4 min
The axial fan provides reliable performance with minimal power consumption, from automotive use and camping equipment to off-grid living and industrial machinery, the axial fan has become a popular choice for various applications. However, like other equipment, axial fans may also encounter common issues over time, such as not spinning, excessive noise, and poor cooling performance. In the following text, this article will delve into the causes of these problems with the axial fan and offer practical solutions.
Axial Fan Not Spinning
Possible causes
Power not connected or insufficient voltage: the axial fan is not receiving enough voltage to start.
Broken or loose wiring: the wire connecting the axial fan may be broken or have poor contact.
Damaged motor inside: the motor may be damaged by prolonged use or manufacturing defects.
Solution
Check the power supply: Use a multimeter to measure the voltage to check if it meets the requirements of the axial fan.
Check the connections: Ensure that the positive and negative wires are connected correctly or not, and the connectors must be sturdy, not loose, and there must be no rust.
Test the motor: Connect the axial fan directly to another known good power source. If the fan still does not spin, the motor may need to be repaired or replaced.
Excessive noise from Axial fan
Possible Causes
Worn bearings need to be lubricated: prolonged operation may cause the bearings of the axial fan to wear out and need to be lubricated to reduce friction.
Fan blades are deformed or blocked by foreign objects: deformation of the blades or accumulation of dust and debris may cause the axial fan to make noise.
Installation problems or vibration amplifies noise: unstable fan installation or vibration may result in increased noise.
Solution
Lubricate the bearings: Use silicone oil or light machine oil for lubrication, avoiding using grease that is too thick, or the bearings will not be agile.
Check the blades: Clean the dirt around the axial fan and inspect whether the blades are deformed. Slight deformation can be manually corrected, but severe deformation will require replacement.
Adjust the installation: The fan must be securely installed, adding rubber pads or shims to reduce vibration.
Poor performance of Axial fan
Possible Causes
Low fan power or weak airflow: The airflow from the axial fan is not enough to cool the unit.
Incorrect fan installation: The fan is installed backwards and the airflow is in the wrong direction.
Dust build-up impedes airflow: Dust and debris build-up reduce airflow from the axial fan.
Solution
Check fan specifications: Check whether the fan's CFM and RPM are sufficient. If not, consider upgrading the fan or adding extra cooling components.
Verify mounting orientation: The fan should blow the heat source, not in the inverse direction.
Clean the dust: Clean the fan and its surroundings often, just use compressed air or a soft brush.
Even if the axial fan is of high quality, sometimes it may encounter problems, such as not spinning, unstable rotation speed, loud noise, or poor heat dissipation. These issues are mostly due to unstable power supply, fluctuating voltage, excessive dust, parts wear, or the fan too small. To ensure that the axial fan continues to work stably and efficiently, JLCMC reminds everyone to keep the environment clean, remove dust and debris in the fan and pipeline, ensure that the power supply facilities have sufficient capacity and stable voltage, avoid running out of phase, and regularly replenish or replace the bearing lubrication. In addition, if you are interested in our axial fan, simply click on the image below to register and receive a special offer of $19 off, so act now and let JLCMC help you achieve a more efficient and reliable cooling solution!
Keep Learning
Why Do Your Drawer Slides Get Stuck, How to Fix It?
Drawer slides are everywhere in your workshop, kitchen, office, or bedroom. Ensuring their smoothness and durability is key to maintaining the convenience and comfort of your furniture. If you're reading this article, you've likely faced the frustration of drawer slides getting stuck. Let's explore why this happens and how JLCMC can help you prevent it and find effective solutions. Common Issues and Analysis Incorrect Drawer Slide Selection One of the most common causes of stuck drawer slides is choos......
Hoses and Clamps Multi-Scenario Leak Repair Guide
Fig. 1 A picture of Hose Clamps In high-performance environments, system failures aren’t always triggered by failing sensors or seized motors. More often than not, it’s the hose and clamps—small, everyday components—that quietly undercut performance. Industry data suggests that nearly 15% of hydraulic system leaks can be traced back to poor-quality fittings, components, and hose and clamp connections. Why these happenings? It starts with something as simple as a poor fit or mismatched hose clip. Left ......
What Happens When a Timing Belt Breaks?
Fig. 1 A picture of a Timing Belt You're cruising comfortably down the highway when suddenly the engine sputters, stutters, and quits. No warning. No check engine light. Just an eerie silence. If the timing belt broke or the cam belt snapped, you've just experienced one of the most damaging failures an engine can suffer. Whether it's in a vehicle or industrial machine, a timing belt is the quiet hero that synchronizes your engine's internal components. It keeps the crankshaft and camshaft in lockstep ......
5 Ball Valve Mistakes That Can Wreck Your Machine Systems—and How to Avoid Them
Alt: A picture of Ball Valve applications In industrial and commercial systems, the smallest hardware often dictates the biggest outcomes. The ball valve—while compact—plays a pivotal role in regulating flow, managing pressure, and maintaining operational integrity. Yet, despite their small size, ball valve failures remain one of the leading causes of machine downtime. In many industrial systems, valve-related issues disrupt uptime more often than motors or controls. Not software. Not sensors. Just va......
Compression Springs in Manufacturing: 5 Machine Failures You Can Prevent Today
Fig. 1 A picture of a Compression Spring In CNC systems and automated equipment, machine failure rarely starts with a loud bang. It begins with something quieter: a drifting axis, a stalled actuator, or inconsistent pressure in a tool head. Often, the underlying cause is force instability, and behind that? A worn or improperly specified compression spring. These small, coiled components play an outsized role in industrial reliability. They manage loads, absorb shock, reset motion, and protect precisio......
How to Prevent Spline Shaft Failures: 7 Pro Tips for Reliable Performance
Fig. 1 A picture of Custom Spline Shafts A slipping servo. A robot arm that jitters. A CNC table that won’t return to zero. You’ve ruled out the usual suspects—belts, bearings, backlash. The real issue might not be what’s loudest or most worn. It’s often a mismatch deep in the motion system—an overlooked spline shaft. Recent studies show that over a third of motion control failures come from misapplied or mismatched splined shafts. These aren’t dramatic breakdowns—they’re the quiet killers: misalignme......